Latest topics
» F/B 1957 Cruiser 75 Carbs
Today at 10:30 pm by kerabo

» Fuel Stabiliser
Today at 10:06 pm by bill2b

» Falcon 67 Parts
Today at 5:24 pm by TonyC

» cruiser 80 brakes
Today at 9:25 am by Miday

» oil seals for mid 50s rear shocks
Sun Feb 18, 2018 9:07 pm by bill2b

» oil seals for mid 50s rear shocks
Sun Feb 18, 2018 7:37 pm by bill2b

» More carb problems
Sun Feb 18, 2018 7:26 pm by Sgtbiro

» trials shake down run( a few teething problems) bike and rider
Sun Feb 18, 2018 7:26 pm by denman

» cruiser sports
Sun Feb 18, 2018 5:37 pm by sportscruiser


AMC 20T little end needed

Go down

AMC 20T little end needed

Post  rob spence on Thu Jan 25, 2018 11:46 am

Anyone got one? Villiers services have none.

rob spence

Posts : 104
Join date : 2017-03-20

Back to top Go down

Small end

Post  kerabo on Thu Jan 25, 2018 1:01 pm

I fitted one but it was 6 years ago. I think I came from Nametab. They are no more but he may have something left.
I dare say you could get one made.
Have you tried a new pin in it before you condem it.
They will need honing to give a perfect fit.
If all else fails there are several scrap cranks and bottom ends on eBay so you could remove one from a scrap unit

Ken
avatar
kerabo

Posts : 2222
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: AMC 20T little end needed

Post  rob spence on Thu Jan 25, 2018 1:04 pm

THANKS KEN,

rob spence

Posts : 104
Join date : 2017-03-20

Back to top Go down

Nametab engineering

Post  piston 197 on Thu Jan 25, 2018 1:34 pm

Nametab is still in operation, just different base, 01527-60395 might be worth asking ?

JH
avatar
piston 197
Moderator

Posts : 3746
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: AMC 20T little end needed

Post  Cruiser79 on Thu Jan 25, 2018 2:53 pm

Alpha Bearings used to make them, worth a try. Pic of their old catalogue attached

avatar
Cruiser79

Posts : 70
Join date : 2009-03-05
Location : Dublin

Back to top Go down

Re: AMC 20T little end needed

Post  rob spence on Thu Jan 25, 2018 3:17 pm

Thanks for the info Cruiser97.

rob spence

Posts : 104
Join date : 2017-03-20

Back to top Go down

Re: AMC 20T little end needed

Post  rob spence on Thu Jan 25, 2018 5:08 pm

I rang Alpha...they make them for Villiers services and apparently there is an order due for about a month away. So if all else fails there will be some eventually.

rob spence

Posts : 104
Join date : 2017-03-20

Back to top Go down

Re: AMC 20T little end needed

Post  peter@dunfordconstruction on Thu Jan 25, 2018 8:13 pm

I should try Bantam John he has loads of AMC parts

peter@dunfordconstruction

Posts : 213
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

Re: AMC 20T little end needed

Post  rob spence on Fri Jan 26, 2018 9:33 am

Thanks Peter, I'd rather not phone Bantam John, it's never a pleasant experience !

rob spence

Posts : 104
Join date : 2017-03-20

Back to top Go down

Re: AMC 20T little end needed

Post  peter@dunfordconstruction on Fri Jan 26, 2018 3:21 pm

Hi Rob,

Sorry to hear your experiences He is a bit gruff but I found him most helpful and quick with the parts and he had everything I wanted

peter@dunfordconstruction

Posts : 213
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

Re: AMC 20T little end needed

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum