Latest topics
» F/B 1957 Cruiser 75 Carbs
Today at 10:13 pm by Ianh

» Double lift centre stand
Today at 9:24 pm by Ianh

» 8e crankcase
Today at 9:00 pm by alan67

» VILLIERS 1H
Today at 8:14 pm by ScottT

» 8E Lighting Coils
Today at 2:38 pm by piston 197

» Farkle Garage
Today at 10:45 am by MoscowFlyer

» Falcon 67 Parts
Today at 10:05 am by TonyC

» Cruiser 1955
Yesterday at 9:56 pm by Ianh

» VILLIERS 1H
Yesterday at 9:17 pm by Ianh


Original drawings

Page 2 of 2 Previous  1, 2

Go down

Original drawings

Post  MoscowFlyer on Sat Aug 05, 2017 5:18 pm

Having studied both these lift cam designs, I think the lower one is a more advanced design. Looking at the top one it lifts the bike all in one go, whereas the lower one would lifts it more gently while reaching the same point, I would like to try it to see, but I only have the one. Mike

avatar
MoscowFlyer

Posts : 1065
Join date : 2008-02-21
Age : 71
Location : Leicestershire

Back to top Go down

cam differences

Post  piston 197 on Sat Aug 05, 2017 5:49 pm

Top one looks like Cruiser 80, other one looks like Cruiser 71/75 ?? stand lift mechanism is different because of exhaust run ( L/H on Villiers and R/H on AMC), the 84 ones while the same hand as the 80 seem to have an extra tip on them rather the rounded top of the 80??

JH
avatar
piston 197
Moderator

Posts : 3752
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

CAD

Post  Bigjim on Sat Aug 05, 2017 9:16 pm


based on the images and that the AF of the hex is 13mm, this is what it might look like
avatar
Bigjim

Posts : 141
Join date : 2016-06-13

Back to top Go down

Cams etc.

Post  mike Sayer on Sun Aug 06, 2017 2:44 pm

Kim, I don`t think your comment regarding cutting off & welding on another bit would work (your post 2am yesterday), the cams on the 84 need to be a close [b]sliding[b] fit on the hexagonal (or square) operating arm, otherwise the whole kaboosh couldn`t be assembled or taken apart.--or have I misinterpreted your thoughts? Embarassed
These comments of mine solely refer to the 84 high lift stand, as Manuel would say "I know nothing about the 80"
Mike Sayer.
avatar
mike Sayer

Posts : 230
Join date : 2008-02-12
Age : 78
Location : east of England

Back to top Go down

Stand Parts

Post  Sgtbiro on Sun Aug 06, 2017 2:58 pm

[quote="MoscowFlyer"]

DOUBLE CLICK on the PICTURE to Enlarge


Hi Do you actually have these parts
Cheers Kevin.

Sgtbiro

Posts : 84
Join date : 2017-04-20

Back to top Go down

high lift cam V2 (the top one)

Post  Bigjim on Sun Aug 06, 2017 5:50 pm


this is the top cam from the twin pictured ones
avatar
Bigjim

Posts : 141
Join date : 2016-06-13

Back to top Go down

Stand Parts

Post  MoscowFlyer on Sun Aug 06, 2017 8:15 pm

Hi Kevin, Yes I have the parts but I need them for my next project, good luck with having some made, if that's the way you go. Mike

Double Lift Cams

Click on Picture
avatar
MoscowFlyer

Posts : 1065
Join date : 2008-02-21
Age : 71
Location : Leicestershire

Back to top Go down

Can we send you a plastic version, do you can compare against your metal ones?

Post  Bigjim on Sun Aug 06, 2017 10:42 pm

MoscowFlyer wrote:Hi Kevin, Yes I have the parts but I need them for my next project, good luck with having some made, if that's the way you go. Mike

Double Lift Cams

Click on Picture
avatar
Bigjim

Posts : 141
Join date : 2016-06-13

Back to top Go down

Stand Parts

Post  MoscowFlyer on Mon Aug 07, 2017 8:43 am

Hi BJ, no problem I'll PM you my address. Mike
avatar
MoscowFlyer

Posts : 1065
Join date : 2008-02-21
Age : 71
Location : Leicestershire

Back to top Go down

Re: Original drawings

Post  Sponsored content


Sponsored content


Back to top Go down

Page 2 of 2 Previous  1, 2

Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum