Latest topics
» Rechroming
Today at 6:14 am by kerabo

» Fulmar 88 or 90?
Today at 6:09 am by fulmar88

» Kestrel 69 fork seals take two.
Yesterday at 11:29 am by johnh

» AMC Carb manifold
Yesterday at 10:42 am by piston 197

» Opions sort on FB Cruiser 80 250cc as a rideable bike.
Yesterday at 8:30 am by casperboat

» NEW CLUB MEMBERS
Sun Aug 20, 2017 5:34 pm by casperboat

» AMC gudgeon pin removal
Sun Aug 20, 2017 1:35 pm by piston 197

» Hi from Barnsley, S Yorks, UK
Sun Aug 20, 2017 9:58 am by piston 197

» VILLIERS ENGINE
Sun Aug 20, 2017 9:58 am by MR SINBAD


Armours exhaust for FB Powerbike 56

View previous topic View next topic Go down

Armours exhaust for FB Powerbike 56

Post  FB vincent on Sat Dec 10, 2016 9:45 am

I recently purchased an exhaust system for my brother's 2F engined Powerbike 56. The design was specified by FB expert Des Heckle, but neither Armours or Des can provide the clamp and cup for the pipe to silencer seal. Can anyone either provide these items, suggest a source or let me know how they have overcome this problem? PM me if you can help and I will let you know my email address. Sandy Ross

FB vincent

Posts : 559
Join date : 2009-01-20
Location : Hertfordshire

Back to top Go down

Exhaust

Post  kerabo on Sat Dec 10, 2016 4:34 pm

Sandy
I have my exhaust back now. Tell me again what you wanted to know.
Regards Ken
avatar
kerabo

Posts : 2016
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Powerbike Exhaust

Post  peter@dunfordconstruction on Sat Dec 10, 2016 6:36 pm

What diameter is the pipe as I might have a clamp

Peter

peter@dunfordconstruction

Posts : 156
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

pipe size

Post  piston 197 on Sat Dec 10, 2016 7:57 pm

Tiny pipe should be 1 1/8" for the Model 56

JH
avatar
piston 197
Moderator

Posts : 3516
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Powerbike exhaust system

Post  FB vincent on Sun Dec 11, 2016 8:57 am

peter@dunfordconstruction wrote:What diameter is the pipe as I might have a clamp

Peter

Peter,

The o.d. of the original (non detachable silencer) system was 1 1/16", as measured from two 1951 pipes. The Armours replacement pipe is approx 1/32" greater in diameter than this. It is possible that the later detachable silencer pattern used a larger diameter, as quoted by JH..

Interestingly New Hudson used pipes of 1 3/16" o.d.

Any help appreciated!

Sandy

FB vincent

Posts : 559
Join date : 2009-01-20
Location : Hertfordshire

Back to top Go down

Exhaust

Post  kerabo on Sun Dec 11, 2016 9:33 am

Sandy can you pm me your email address please.
I can't remember how yo out pictures on the forum.
Regards Ken
avatar
kerabo

Posts : 2016
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Exhaust

Post  kerabo on Sun Dec 11, 2016 9:37 am

It's ok Sandy my iPad had remembered your email
Pictures on the way.

The front pipe is 1.127" whatever that translates to.. The exhaust clamp is a normal twin section clamp with a bolt through it. The seal is the tricky bit. It's a concave washer about 3/8" deep with a seal inside held in place by the clamp. The silencer is squeezed up to that seal by a through stud right through the middle of the silencer.
Ken
avatar
kerabo

Posts : 2016
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

sizes

Post  piston 197 on Sun Dec 11, 2016 5:07 pm

I said 1/4" Ken measures 1.127" ok so I was 2 thou out, about the thickness of the chrome ?
JH
avatar
piston 197
Moderator

Posts : 3516
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: Armours exhaust for FB Powerbike 56

Post  peter@dunfordconstruction on Sun Dec 11, 2016 5:55 pm

Hi Regret Mine all too big!

Peter

peter@dunfordconstruction

Posts : 156
Join date : 2014-10-28
Location : Lymington Hampshire

http://peter@dunfordconstruction.co.uk

Back to top Go down

Re: Armours exhaust for FB Powerbike 56

Post  Sorcererflyer on Sun Dec 11, 2016 8:35 pm

piston 197 wrote:I said 1/4" Ken measures 1.127" ok so I was 2 thou out, about the thickness  of the chrome ?
JH

1.125 is I and one eighth, 1.25 is 1 and a quarter, surely?

Sorcererflyer

Posts : 20
Join date : 2014-05-07

Back to top Go down

Its been a long day !

Post  piston 197 on Sun Dec 11, 2016 8:42 pm

Yes you are correct, was up at 4am this morning, must get thinking and typing in sync !
Incidentally on Armours exhaust pipe listings product No ARMFB56 ( powerbike model 56) it states the pipe to be 1 1/8" ?? now they could be wrong ??
JH
avatar
piston 197
Moderator

Posts : 3516
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: Armours exhaust for FB Powerbike 56

Post  Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum