Latest topics
» Interesting idea for CDI ignition on youtube.
Today at 8:49 am by rob spence

» Wiring for AMC trials
Yesterday at 9:58 pm by Bigjim

» cruiser 80 chain guard
Yesterday at 9:27 pm by william105

» Can anyone identify these pistons?
Yesterday at 4:02 pm by piston 197

» AMC 20T piston rings
Yesterday at 10:03 am by rob spence

» AMC engined Plover - Wont start
Mon Sep 18, 2017 8:23 am by Davidohyeah

» 1H Starting
Sun Sep 17, 2017 9:47 am by Jack Clegg

» Rolling 40 year MoT exemption starts May 2018
Fri Sep 15, 2017 6:48 pm by John Wakefield

» 1H ENGINE PARTS
Fri Sep 15, 2017 5:40 pm by Bigjim


6" front brake

View previous topic View next topic Go down

6" front brake

Post  kerabo on Wed Jul 20, 2016 12:44 pm

Can anyone tell me the correct sequence for the spacers and washers on the normal 6" FB front hub. I could do it with trial and error but it makes life easier if someone know.
So spacers and the depth of them and where are washers used. Am I right in thinking one wheel nut is longer and floats until the wedge is tight. The other bottoms in the recessed nut?

Thanks Ken
avatar
kerabo

Posts : 2019
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

wheel nut

Post  piston 197 on Wed Jul 20, 2016 1:54 pm

Both wheel nuts are the same length ! ( will post your brake arm in the morning)
JH
avatar
piston 197
Moderator

Posts : 3543
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

front Brake

Post  kerabo on Wed Jul 20, 2016 2:13 pm

Am I right in thinking the nuts float to let the fork legs equalize and then clamp with the wedges . I know one side goes into the recessed deep nut.
Regards Ken
avatar
kerabo

Posts : 2019
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

about right

Post  piston 197 on Wed Jul 20, 2016 2:38 pm

Best to pull up the brake side first to get maximum engagement with the brake stop, do up the wedge that side, then tighten up the opposite side and do up that wedge
JH
avatar
piston 197
Moderator

Posts : 3543
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: 6" front brake

Post  kerabo on Wed Jul 20, 2016 4:10 pm

piston 197 wrote:Best to pull up the brake side first to get maximum engagement with the brake stop, do up the wedge that side, then tighten up the opposite side and do up that wedge
JH
Thanks John

Regards Ken
avatar
kerabo

Posts : 2019
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: 6" front brake

Post  Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum