Latest topics
» Still looking
Yesterday at 8:43 pm by Sgtbiro

» Leaky Seagull
Yesterday at 9:06 am by keith.hodgenia

» Falcon 87 wiring
Wed Jul 26, 2017 9:17 pm by kerabo

» Cruiser 80 centre stand parts wanted
Wed Jul 26, 2017 2:49 pm by Sgtbiro

» falcon final drive sprocket
Wed Jul 26, 2017 1:47 pm by piston 197

» Cruiser 39 exhaust repairs in Australia, carby, etc etc.
Wed Jul 26, 2017 10:55 am by Maurice Chivers

» Falcon 81 wiring..
Wed Jul 26, 2017 8:02 am by FB vincent

» Belgian Powerbike 98cc
Wed Jul 26, 2017 6:54 am by FB vincent

» NEW CLUB MEMBERS
Tue Jul 25, 2017 8:18 pm by 1953Man


14A flywheel removal

View previous topic View next topic Go down

14A flywheel removal

Post  Mike Neden on Sat May 07, 2016 6:22 pm

I'm assuming that the nut undoes anti-clockwise?

Thanks

Mike Neden

Posts : 27
Join date : 2015-10-15

Back to top Go down

flywheel nut

Post  piston 197 on Sun May 08, 2016 5:43 am

I am assuming you are referring to the Brass flywheel /magneto retaining nut ( some 14A engines have a flywheel on the opposite side of engine as well) then yes standard r/hand thread nut, that will loosen and then go tight again as it acts as an extractor to self extract the flywheel from the tapered shaft .
JH
avatar
piston 197
Moderator

Posts : 3458
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: 14A flywheel removal

Post  Mike Neden on Sun May 08, 2016 5:53 pm

Thanks John

It's the cast iron flywheel on the opposite side to the mag. It's on proper tight and I may have to admit defeat.

Mike Neden

Posts : 27
Join date : 2015-10-15

Back to top Go down

flywheel

Post  piston 197 on Sun May 08, 2016 5:56 pm

If it is just the nut that is tight, do not be frightened to get the "black and red spanner" on it ( or oxy-acetylene as some call it , heat works wonders !
JH
avatar
piston 197
Moderator

Posts : 3458
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: 14A flywheel removal

Post  Mike Neden on Sun May 08, 2016 7:28 pm

Yeah, after almost breaking my back, I'll be getting my friendly mechanic to apply some heat. I need the nut to go a rebuilt engine. Is there any knack to doing it up? I was thinking of holding the mag side nut at the same time.
Ta

Mike

Mike Neden

Posts : 27
Join date : 2015-10-15

Back to top Go down

nuts

Post  piston 197 on Sun May 08, 2016 7:34 pm

if you hold the mag flywheel nut it will probably undo rather than the one you are trying to remove ( sod's law and all that)
If the engine is out of the frame, can you not clamp the flywheel in a vice jaws

JH
avatar
piston 197
Moderator

Posts : 3458
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Re: 14A flywheel removal

Post  Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum