Latest topics
» Falcon 67 Parts
Today at 12:05 pm by fulmar88

» Wanted Scrap Rear Sprocket
Today at 11:50 am by kerabo

» F/B 1957 Cruiser 75 Carbs
Today at 11:11 am by peter@dunfordconstruction

» Fuel Stabiliser
Today at 6:59 am by piston 197

» cruiser 80 brakes
Yesterday at 9:25 am by Miday

» oil seals for mid 50s rear shocks
Sun Feb 18, 2018 9:07 pm by bill2b

» oil seals for mid 50s rear shocks
Sun Feb 18, 2018 7:37 pm by bill2b

» More carb problems
Sun Feb 18, 2018 7:26 pm by Sgtbiro

» trials shake down run( a few teething problems) bike and rider
Sun Feb 18, 2018 7:26 pm by denman


Member needs spares

Go down

Member needs spares

Post  kerabo on Tue Jan 12, 2016 8:08 pm

I have had a call frm a member who has a Cruiser 68. He is short of a rear hub and a seat to make his bike complete. He says it's not a full width hub. It don't mean much to me but I said I would post on here for him.
If anyone can help with spares or advice please let me know and I will contact him.

Regards Ken
avatar
kerabo

Posts : 2226
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Cruiser 68 rear hub

Post  piston 197 on Tue Jan 12, 2016 8:18 pm

Unusual rear hub, used for one year only (1954)it is basically the same as a Falcon 58/67 rear hub, but it is a 6" item instead of 5" used in the Falcons, would be easy to make one, by getting a normal 6" cruiser rear hub, stripping out the centre alloy trim and turning down the flange opposite to the brake drum to smaller diameter ( approx. 3") and drilling for spokes, or alternatively if you were not fussy you could just use the later 6" hub from the Cruiser 75,80,84 and 89, it would not be "right" but would do the same job ?
JH
avatar
piston 197
Moderator

Posts : 3748
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Cruiser 68 rear hub

Post  MoscowFlyer on Tue Jan 12, 2016 9:09 pm

Hi, here is a diagram of the rear hub in question. Mike

avatar
MoscowFlyer

Posts : 1064
Join date : 2008-02-21
Age : 71
Location : Leicestershire

Back to top Go down

Rear hub

Post  kerabo on Wed Jan 13, 2016 8:28 pm

Thank you John and Mike.
I will pass your ideas on to him. As you say John that would be reasonably easy so long as care was taken . Do you think the spindle and brake backplate would fit from a later cruiser?
Regards Ken
avatar
kerabo

Posts : 2226
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Will it fit ?

Post  piston 197 on Wed Jan 13, 2016 8:53 pm

It is the same swing arm and brake plate so cannot see why not ? and the later ones have the benefit of having a sprocket that is detachable from the brake drum, early model 71 and the half width Cruiser 68 ones have the sprocket and brake drum all in one .
JH
avatar
piston 197
Moderator

Posts : 3748
Join date : 2008-08-17
Location : ross-on-wye

Back to top Go down

Hub

Post  kerabo on Wed Jan 13, 2016 8:56 pm

Thanks John
Will pass that on .
Regards ken
avatar
kerabo

Posts : 2226
Join date : 2008-02-11
Age : 67
Location : Falcon 87. Trials 93 Special. Powerbike 56. Falcon 81 Green Lane bitsa. Sunbeam S8. Honda Deuville.

Back to top Go down

Re: Member needs spares

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top


 
Permissions in this forum:
You cannot reply to topics in this forum